Part No: AN712Issued year: 2011File size: 0.09mbFile type: pdf
The following methods have been developed for the selective extraction of tobacco specific nitrosamines (NNN, NNK, NAT, and NAB) from human urine. The method is highly reproducible and offers an average recovery of 80% (95% for NNK and NAT; and 70% for NNN and NAB). Detection limits of 4 pg/mL are readily achieved for urine samples using LC-MS-MS analysis.
MIP, SupelMIP, Molecularly Imprinted Polymer,
Part No: P145Issued year: 2016File size: 0.42mbFile type: pdf
This poster demonstrates a rapid and reliable sample preparation method using Supported Liquid Extraction (ISOLUTE SLE+) to extract a suite of 30 hormone analytes from a hydrolyzed urine matrix. Single injection analysis by LC-MS/MS shows that matrix effects are eliminated by the ISOLUTE SLE+ protocol and that analyte recovery and sensitivity have excellent clinical utility.
Part No: AN880Issued year: 2017File size: 3.38mbFile type: pdf
The method described in this application note achieves high reproducible extraction recoveries of vitamin B7 from serum while minimizing co-extractable material in the form of proteins, lipids and phospholipids. Serum is extracted using the EVOLUTE® EXPRESS ABN 96-well plate.
Part No: AN757Issued year: 2012File size: 1.61mbFile type: pdf
Vitamin D deficiency can result in a variety of health issues such as osteoporosis, liver and kidney problems, it is often associated with increased risk of cancers and multiple sclerosis. From this standpoint vitamin D monitoring is on the rise and of significant clinical relevance. This method describes the use of ISOLUTE SLE+ plates for the efficient and simple extraction of the vitamin D metabolites 25-OH vitamin D2 and 25-OH vitamin D3. Incorporated into the procedure is an integral protein binding disruption step which maximizes analyte recovery and eliminates the need for any offline protein disruption. This method has been internally validated using DEQAS approved serum samples and deuterated internal standards the results obtained are better than that required for criteria for acceptable performance for
DEQAS approval. All recoveries were consistently greater than 90% with all RSDs < 10% at LOQs of 1-3.75 ng/mL.
Vitamin, Vitamin D, VitaminD, D, Clinical, SLE+, SLE, ISOLUTE, Metabolites, Supported Liquid Extraction, 25 Hydroxy Vitamin D,
Part No: AN706Issued year: 2011File size: 0.1mbFile type: pdf
The following methods have been developed for the selective extraction of beta-agonists from biological matrices. Methods have been developed for both biological tissues (e.g. bovine muscle) and fluids (e.g. urine). The methods are highly reproducible and offer β-agonist recoveries in the range of 35-90%.
MIP, Molecularly Imprinted Polymers, BIOTAGE, AFFINILUTE, SupelMIP,
Part No: Issued year: 2013File size: 0.52mbFile type: pdf
Developed in collaboration with the OC Crime Lab, this poster describes the extraction of 25 benzodiazepines and sedatives from various matrices using ISOLUTE SLE+ Supported Liquid Extraction columns. This poster was presented at SOFT 2013.
Part No: Issued year: 2010File size: 1.23mbFile type: pdf
User report: Initiator. Prof. Nakamura at the Gakushuin University has described the Initiator as an essential tool for his group’s cutting-edge research. We asked Prof. Nakamura for his views on the latest trends in the fields of organic synthesis and drug discovery.
Part No: P049Issued year: 2012File size: 0.27mbFile type: pdf
This poster outlines a new method for the extraction of a mixture of peptides from plasma using resin based SPE. Initial method optimization was performed using EVOLUTE ABN before comparison to the streamlined approach without plate conditioning and equilibration using EVOLUTE EXPRESS ABN. Presented at EBF 2012.
EBF, EBF 2012, Peptide, ABN, SPE, Polymer, Polymeric,
Part No: AN903 (2)Issued year: 2004File size: 0.14mbFile type: pdf
The rapid synthesis of the non-steroidal anti-inflammatory agent Fenclofenac (2-(2,4-dichlorophenoxy)phenyl acetic acid) under microwave irradiation is reported. Modified reaction conditions of traditional Ullmann ether coupling resulted in high yields of the diaryl ether. The Willgerodt–Kindler transformation and subsequent hydrolysis of thioamide resulted in 52%
overall yield of Fenclofenac.
Part No: AN016-HORIssued year: 2009File size: 1.28mbFile type: pdf
This application note uses the Biotage® Horizon 4790 automated extraction system with a DVB SPE disk to extract an aqueous sample for PAH compounds analysis. The extract is dried using the Horizon Technology DryDisk®.
Part No: AN806Issued year: 2013File size: 1.03mbFile type: pdf
The screening of patient urine samples for basic drugs is typically performed following a lengthy sample preparation methodology that requires a time consuming dry down step.
A novel elution protocol coupled to the EVOLUTE EXPRESS advanced plate technology affords a fast sample preparation solution that follows a LOAD-WASH-ELUTE-ANALYZE strategy. Basic drugs are fortified into urine and extracted in 3 easy steps using EVOLUTE EXPRESS CX solid phase extraction in a 96-well plate format.
Part No: AN794Issued year: 2013File size: 1.01mbFile type: pdf
This application note describes a method of extraction for metanephrine and normetanephrine from pooled
plasma using EVOLUTE® EXPRESS WCX 96-well SPE plates.
A new solid phase extraction
technology has been developed to reduce the time
associated with sample preparation methods by eliminating
traditional steps in the extraction workflow. Leveraging this
technology, a method protocol was developed using a load,
wash and elute approach. This method was optimized for
Part No: AN795Issued year: 2013File size: 1.09mbFile type: pdf
This application note describes a method of extraction for metanephrine and normetanephrine from synthetic
urine using EVOLUTE® EXPRESS WCX 96-well SPE plates.
A new solid phase extraction technology has been developed to reduce
the time associated with sample preparation methods by
eliminating steps in the extraction workflow. Leveraging this
technology, a method protocol was developed using a load,
wash and elute approach. This method was optimized for
Part No: AN080Issued year: 2013File size: 0.26mbFile type: pdf
This application note describes a method for sample preparation
of different matrixes prior to amino acid analysis according to IS
ISO 13903:2005 or the similar AOAC Official Method 994.12 using
Biotage® Initiator+ to speed up the process.
Part No: PPS436.v1Issued year: 2016File size: 0.17mbFile type: pdf
Sanford Burnham Prebys Case Study.
Fewer transfers and the ability to evaporate difficult solvents right in
the scintillation vial has made Biotage® V-10 the go-to evaporator at
Sanford Burnham Prebys (SBP), a top medical research institute.
Part No: PPS491Issued year: 2018File size: 0.68mbFile type: pdf
Purification is a fundamental step in drug discovery. As
pioneers of automated flash purification, Biotage is your
ideal partner. When it comes to purification, here are five reasons to
Part No: TN-0012.0806Issued year: 2008File size: 0.09mbFile type: pdf
Biotage FLASH 400™ Production-Scale System The FLASH 400 is a complete skid-mounted system designed for large-scale flash chromatography and adsorption purification. The FLASH 400 uses prepacked cartridges and radial compression for performance and reliability. Built with industrial-grade components that are appropriate for operations under FDA regulations and cGMP standards, the FLASH 400 is rapidly becoming the first choice of pharmaceutical and contract manufacturing companies around the world for critical purification applications.
Part No: AN059Issued year: 2012File size: 0.63mbFile type: pdf
Flash chromatography is the primary technology for separating, purifying, and isolating both synthetic organic compounds and natural products. Until recently, automated flash purification systems were limited to user-selected detection and collection wavelengths to fractionate separated compounds from sample mixtures. In this application note we demonstrate how the advances in Isolera Spektra are used in the purification of a spinach extract.
Part No: AN060Issued year: 2012File size: 1.02mbFile type: pdf
Isolera Spektra provides definitive fraction purity assessment
in both 2-D and 3-D prior to any post flash analysis. With this
information chemists quickly know if a fraction contains a pure
product suitable for further mass and structure confirmation
or whether the impure fractions must be re-purified. This
knowledge improves synthesis throughput and avoids any
embarrassment of submitting impure fractions for analytical
Part No: AN092.v1Issued year: 2014File size: 1.12mbFile type: pdf
The UV absorption spectrum of some solvents
overlaps with the product they dissolve, meaning
that fraction collection processes cannot distinguish
between solvent and product. Luckily, there is
technology that solves this problem.
Flash purification is a separation technique developed in 1978 by Professor W.C. Still that uses a stationary phase (a column or cartridge filled with an insoluble solid support) and a mobile phase (elution solvent mixture) to separate and purify a mixture of organic compounds.
Part No: AN095Issued year: 2014File size: 0.65mbFile type: pdf
Elution of polar molecules in flash chromatography sometimes requires solvent additives, making purification more cumbersome. The Isolera™ family of flash purification instruments and Biotage® SNAP KP-NH cartridges significantly reduce the extra work involved.
Part No: TN-0006.0806Issued year: 2006File size: 0.86mbFile type: pdf
Purify up to 400 grams of compound at 1 L/min with the Biotage Flash 150™ system, up to 2x faster than traditional glass columns. This robust stainless steel system safely operates at 100 psi enabling high flow rates and the use of higher viscosity solvents. A variety of cartridge media provides
chemists with selectivity choices for optimal purification conditions. Simple and reliable, this system contains everything needed to begin your separations.
Part No: TN407.1107Issued year: 2007File size: 0.07mbFile type: pdf
FlashVac-10 and -20 Sample Processing Manifolds are used
to process standard Luer tipped ISOLUTE work-up columns.
Constructed from glass or high density polyethylene, the
FlashVac manifolds are compatible with commonly used
reaction and work-up solvents.
Part No: AN086.v2Issued year: 2014File size: 1.02mbFile type: pdf
A novel resin from MIP Technologies, RENSA® PY, is able to fractionate colored compounds present in beetroot juice using mild and purely aqueous elution conditions without the use of salts or organic solvents.
Part No: Issued year: 2015File size: 1.88mbFile type: pdf
User Report: Isolera™ Dalton, Okayama University. The laboratory of Prof. Hiroyuki Miyachi at Okayama University installed Biotage’s Isolera Dalton, an automated mass-directed purification system for flash chromatography, allowing the fractionation and collection of optical isomers. “I felt like the world’s first mass-detection automated purification system had finally arrived.”
Part No: AN792Issued year: 2013File size: 2.3mbFile type: pdf
This application note describes fully automated liquid handling of the extraction of a range of drugs from urine, which are typically screened for forensic toxicology panels, using ISOLUTE® SLE+ 96-well supported liquid extraction plates.
drugs of abuse, TECAN, automated, ISOLUTE SLE+
Part No: AN115Issued year: 2018File size: 0.49mbFile type: pdf
This application note describes optimization for a fully automated synthesis and on-resin cyclization of oxytocin enabled by Branches™, a unique software feature of the Biotage® Initiator+ Alstra™ peptide synthesizer.
Part No: P150Issued year: 2016File size: 0.39mbFile type: pdf
Interest in peptide-based therapeutics has risen dramatically over the last decade. More specifically, significant energy has been dedicated to cyclic peptides, their synthesis, their biological activity, and their biological stability as potential alternatives to their linear counterparts. However, synthesizing a cyclic peptide creates significant challenges not encountered in linear peptide synthesis.
Herein we present a synthesis of oxytocin describing optimization for fully automated, on-resin disulfide bond formation utilizing Branches™, a unique feature enabling visualization and specific programing for cyclic and branched peptide synthesis. We will highlight the transferability of this optimized synthesis to larger scale syntheses and conclude with the fully automated synthesis of cyclized oxytocin incorporating an isotopically labeled Leu residue, enabling use as an internal standard in MS experiments.
Part No: TN113Issued year: 2006File size: 0.09mbFile type: pdf
ISOLUTE Confirm HCX columns are based on cation exchange and C8 mixed mode chemistries. Basic drugs are therefore retained by two primary retention mechanisms - ionic and non-polar. This allows a more rigorous interference elution regime to be used, leading to a very clean final extract, as many non-polar interferences which are retained by a non-polar interaction alone, can be eluted selectively, prior to elution of the drug.
Part No: P024Issued year: 2008File size: 1.9mbFile type: pdf
It is well known that traditional liquid-liquid extraction (LLE) provides very clean extracts prior to LC/MS analysis. Supported liquid extraction is analogous to traditional LLE, however, analyte partitioning takes place using an inert support material, rather than two immiscible liquids. This provides excellent extraction efficiencies while alleviating many of the tedious liquid handling issues associated with LLE.
Part No: TN116Issued year: 2006File size: 0.07mbFile type: pdf
The extraction of basic drugs from biological fluids using a purely non-polar retention mechanism (e.g. C4, C8 or C18) can lead to extracts that contain a large amount of non-polar co-extracted material that can interfere with subsequent analysis. Conversely, extraction mechanisms based on ion exchange interactions can be non-robust due to the variable ionic strength of the sample matrix.
Part No: TN129Issued year: 2005File size: 0.07mbFile type: pdf
The use of ISOLUTE HCX mixed-mode sorbents is widely accepted for providing high purity extracts of basic drugs from biological fluids. The ISOLUTE HCX-Q sorbent utilizes a combination of weak cation exchange and C8 non-polar retention mechanisms.
Part No: Issued year: 2014File size: 1.02mbFile type: pdf
Testing for drugs of abuse in oral fluids can strongly benefit the criminal justice field as a less invasive and cost-effective approach for drug detection when compared to blood or urine sampling. Oral fluid analysis has facilitated laboratory analysis for many drugs of abuse and is a constantly evolving analysis procedure which benefits from increasingly sensitive methods of detection. The Laser Diode Thermal Desorption (LDTD) source combined with Mass spectrometry is presented as a new screening tool for drug analysis in Oral Fluids. Analysis speed of LDTD provides accurate results in seconds in combination with exceptional specificity of MS instruments make a powerful platform for the screening of different drugs of abuse and new emerging drugs. Different extraction procedures are available; however those methods depend on specific drug conditions: basic or acid drugs / hydrophilic or hydrophobic. A new extraction approach, Supported Liquid Extraction (SLE+) is evaluated as generic extraction procedure.
Part No: UI400Issued year: 2018File size: 0.11mbFile type: pdf
The tasks carried out during the Preventive Maintenance (PM)
visit shall include servicing the listed components and a final
check, which is based on factory acceptance and qualification
tests. These two procedures constitute a Gilson Preventive
Part No: AN056Issued year: 2012File size: 0.2mbFile type: pdf
Quinolines are an important class of broad-spectrum antibiotics1 that were traditionally obtained by refluxing an aniline and diethyl ethoxymethylemalonate (Scheme 1) for several hours often in low yield.2 Heating the reaction mixture by microwaves to temperatures above the boiling points, with or without solvents, improves the yields and shortens the reaction time dramatically.3-6
Part No: AN106Issued year: 2015File size: 0.3mbFile type: pdf
The term “Green Chemistry” has become a major part of the
science community’s lexicon. In this application note we will
look at two areas for flash chromatography:
1. Replacing chlorinated solvents with those considered more
2. Reducing solvent use and waste generation with more
thoughtfully applied chromatography principles.
Part No: P158Issued year: 2017File size: 0.27mbFile type: pdf
As reversed-phase flash chromatography gains traction in
medicinal chemistry labs the need to monitor its cost and
safety are becoming more important. Commonly used
reversed-phase solvents typically include water with an
organic solvent such as methanol or acetonitrile – each
have advantages and disadvantages.
Part No: AN801Issued year: 2003File size: 0.27mbFile type: pdf
The heat flow parameter can be used to monitor the progress of a reaction, and can be useful
in determining reaction rates. A heat flow probe study was executed on the Advantage
Series™ 3400 process chemistry workstation for the hydrolysis of acetic anhydride in water
at temperatures from 25 to 55 °C. The observed rate constant for the hydrolysis was determined
from the heat flow measurements. An Eyring plot was produced and the enthalpy and
entropy of activation were determined. Finally, the heat of reaction was measured based on
the total amount of heat that was observed during the hydrolysis.
Part No: AN036Issued year: 2001File size: 0.55mbFile type: pdf
Activated carbon is an adsorbent media used to remove colored compounds from solution. Using this media in the Biotage FLASH-AC cartridge as a packed bed improves adsorbent performance. Increasing the temperature of the solvent modifies adsorption and alters performance of the decolorization process. Elevated temperatures increase product solubility, therefore requiring less solvent than at room temperature. The increased concentration of product in a hot solution also simplifies crystallization.
Part No: AN040Issued year: 2003File size: 0.4mbFile type: pdf
Research in CNS drugs is primarily centered on nitrogen heterocycle chemistry. Basic amines are difficult to purify using traditional silica chromatography because of strong interactions between acidic silica and the molecules’ basic amine groups. These interactions cause band spreading and poor compound recovery. Solutions employed to counteract this phenomena include adding a competing amine (e.g. triethyl amine or ammonium hydroxide) to the flash chromatography solvent system or using reversed-phase HPLC with a buffered solvent system.
Part No: AN118-HOR.V.1Issued year: 2017File size: 0.48mbFile type: pdf
Hexane extractable material (HEM), also known as Oil & Grease extraction is a simple water quality measurement. The measurement can be used to assess pollution for compliance or as a measure of influent contamination to protect a waste treatment plant from levels that might cause malfunction.
Part No: P172Issued year: 2017File size: 0.49mbFile type: pdf
We investigate the use of reversed-phase high performance flash chromatography (HPFC) to quickly purify large quantities of crude synthetic peptides.
(6th Solid Phase Peptide Synthesis Symposium & 12th Australian Peptide Conference, Queensland, Australia, Oct. 2017)
Part No: Issued year: 2018File size: 0.66mbFile type: pdf
This poster presents a high sensitivity method for extraction and analysis of estrogens in human plasma. Sample preparation utilizes Biotage ISOLUTE SLE+ plates, providing high analyte recovery and low matrix effects.
MSACL 2018, Palm Spings, CA
Part No: AN041-HORIssued year: 2010File size: 0.83mbFile type: pdf
This application note investigates the applicability of automated solid phase extraction using the Biotage(r) Horizon 4790 extractor and DryDisk solvent drying system to extraction of a wide range of different compounds from phenols, to triazines, to organochlorine and organophosphorous pesticides spiked into tap water at a concentration of 1 ug/L.
Part No: Issued year: 2014File size: 0.34mbFile type: pdf
In this poster, an IONICS 3Q 220 triple quadrupole mass spectrometer using a load, wash, elute method protocol with recently advanced solid phase extraction (SPE) sorbent technology (EVOLUTE EXPRESS WCX) was used to perform analysis of the two compounds. As a result low levels of metanephrine and normetanephrine are detectable in plasma with short sample preparation and LC run times. This LC-MS/MS method provides a fast, sensitive, accurate, and reproducible solution for the analysis of ME and NME in plasma.
Part No: AN303Issued year: 2007File size: 0.14mbFile type: pdf
Heck reactions utilizing a thermostable catalyst in combination with microwave irradiation have been performed. A substantial enhancement of reaction rates as well as excellent regiocontrol could be obtained under microwave conditions without using inert gas. A slight increase in yield was also noted.
Part No: CM-HMPB-0810Issued year: 2010File size: 0.29mbFile type: pdf
For peptides acid, we recommend using the HMPB-ChemMatrix
as this resin will provide high crude purity and a recovery yield of
90-95%. The Wang-ChemMatrix will produce similar crude
peptide purity, but the recovery yield is lower (60-70%). On
request, we can provide preloaded HMPB-ChemMatrix resins with
all 20 naturally occurring amino acids. Other amino acids can be
preloaded on special request.
Part No: PPS535Issued year: 2017File size: 0.8mbFile type: pdf
When a new piece of equipment is introduced the question is always raised about performance. Does it perform as well as its predecessor? What about the performance over time? This technical note will provide data to describe the performance of the SPE-DEX 5000, providing solid phase disk extraction (SPE), compared to standards required by environmental methods.
Part No: PPS538.V.1Issued year: 2015File size: 0.29mbFile type: pdf
The quality of the solid phase disk used for extraction is key to the success and ease of an analysis. Horizon Technology’s Pacific™ Premium Oil & Grease SPE disks for Method 1664/ISO 11349 meet all Initial Precision and Recovery (IPR), Method Detection Limit (MDL) and Ongoing Precision and Recovery (OPR) limits specified by the US EPA, while saving the lab extraction time and solvent volume. Both 47 and 100-mm disks are fast-flowing and have a high-retention capability, which increases efficiency without compromising recoveries.
Part No: UI402Issued year: 2019File size: 0.36mbFile type: pdf
Confidence is what you need before you separate your precious
compound on a new brand of flash chromatography column.
Predictably getting your compound in a pure state is what you
want, and if you can get it faster and use less solvent all the
better. After all, your project needs to be completed on time,
and trying something new is not always appealing.
In order to take your first steps toward gaining that confidence
you can follow the same procedures we use here at Biotage to
Part No: AN747Issued year: 2011File size: 0.18mbFile type: pdf
Biotage® PRESSURE+ manifolds deliver positive pressure, parallel processing for 96 well plates and column formats. The systems utilize a consistent, uniform flow of positive pressure to move both low and high viscosity liquids through SPE plates and columns. ISOLUTE SLE+ Supported Liquid Extraction plates and columns offer an efficient alternative to traditional liquid-liquid extraction (LLE) for bioanalytical sample preparation, providing high analyte recoveries, no emulsion formation and greatly matrix effects associated with biofluid analysis.
SLE+, SLE, Supported Liquid Extraction, positive pressure manifold, Pressure+96, Pressure+48
Part No: UI333Issued year: 2015File size: 0.89mbFile type: pdf
If high back pressure is detected in the makeup pump lines, and/or the High Makeup Flow Pressure dialog appears, the microfilter may be partially clogged and needs replacing. This is a step by step guide.
Part No: UI403Issued year: 2019File size: 0.13mbFile type: pdf
Biotage® Sfär columns can be used with CombiFlash Rf and
CombiFlash NextGen Systems. This document outlines how to
set up your CombiFlash instrument for use with Biotage® Sfär
Silica HC and Biotage® Sfär C18.
Part No: UI319.v3Issued year: 2017File size: 0.7mbFile type: pdf
Biotage®SNAP Ultra cartridges are compatible with CombiFlash® Rf Systems. As a convenience, Biotage SNAP Ultra cartridges with Luer slip connectors are available. Contact your Biotage representative for ordering information.
Part No: TechTipIssued year: 2011File size: 0.07mbFile type: pdf
Are you keeping up with your annual six month Hydrophilic Solution treatments for your SPE-DEX 4790 or 1000/3000 SPE-DEX instruments?
1. The water sample will not flow down into the disk holder.
2. My water inlet valve may not be opening
3. My water inlet valve is opening, but my sample is not dispensing into the disk holder.
4. My entire collection vessel is filled with the water sample.
Part No: AN078Issued year: 2013File size: 1.05mbFile type: pdf
In this application note we demonstrate the power of mass detection in Isolera™ Dalton by investigating the incomplete separation of two dyes, Butter yellow (Mass 225.29 g/mol) and Sudan red (Mass 278.31 g/mol), by normal phase flash purification.
Part No: P053Issued year: 2013File size: 1.22mbFile type: pdf
Immunosuppressant drugs are extremely important for therapeutic drug monitoring (TDM) regimes, requiring robust and reliable methods for their analysis. This poster aims to demonstrate strategies for the extraction of various immunosuppressant drugs from whole blood providing clean samples prior to UPLC-MS/MS analysis. Spiked whole blood was extracted using a variety of protocols to investigate optimal combination of drug recovery and extract cleanliness. UPLC-MS/MS was conducted using a Waters ACQUITY UPLC coupled to a Quattro Premier XE triple quadrupole mass spectrometer. Acceptable extraction recoveries were obtained showing excellent extract cleanliness, demonstrating a reliable method for mass spectrometric approaches for these analytes.
Immunosuppressants, SLE, Supported Liquid Extraction, ISOLUTE, MSACL, San Diego, 2013
Part No: P140Issued year: 2016File size: 0.31mbFile type: pdf
Reversed-phase chromatography is typically used when you need to separate several milligrams of relatively polar compounds that either are not soluble in normal-phase solvents or are not compatible with bare silica
because they react, stick, or both. If you are currently using reversed-phase at preparative scale, such as flash chromatography, you know the mobile phase limitations – water with either methanol, acetonitrile, or
THF. As with normal-phase flash chromatography, when it comes time to purify you want your crude sample fully solubilized in the weakest possible solvent at the highest possible concentration.
Part No: AN044-HORIssued year: 2009File size: 0.65mbFile type: pdf
The Biotage® DryVap Concentrator System was intentionally designed to provide enhanced recoveries of semivolatile organic compounds (SVOC) such as those found in EPA Method 8270. The unique design of the DryVap system, which uses a vacuum, sparge gas, and internal immersion heater, allows it to achieve excellent recoveries for a wide range of compounds.
This purpose of this study is to determine the washing
technique for a DryVap® concentrator tube which
optimizes the recovery of both low and high boiling point
Part No: AN075.v2Issued year: 2013File size: 0.49mbFile type: pdf
In this application note we present a new type of polymeric reverse phase adsorbent that is able to provide improved separations of a range of small chemical compounds and also peptides evaluated side by side to a comparable benchmark DVB-Styrene macroporous resin.
MIP, molecularly imprint resins
Part No: AN124-HORIssued year: 2017File size: 1.83mbFile type: pdf
Semivolatile organic compounds (SVOC) have a variety of chemical properties that have been found to cause harmful effects to both humans and the environment. Accurate measurements are challenging to obtain because SVOCs readily adsorb onto surfaces, and are found in common household items such as cleaning agents, personal care products, electrical components, pesticides, water and food.
Part No: AN095-HORIssued year: 2014File size: 2.85mbFile type: pdf
The global demand for fish as a natural source of fresh animal protein, essential fats, minerals, and vitamins continues to rise with the human population. It is estimated that natural fish resources will not be sustainable, creating the need to increase the available supply of fish through aquaculture.
Part No: AN106-HORIssued year: 2016File size: 1.4mbFile type: pdf
Worldwide, there is great concern for the presence of semi-volatile organic compounds in surface water, groundwater, and drinking water, such as Aldrin, extremely toxic to fish and a persistent organic pollutant. China has increased concern about drinking water as sources of surface and groundwater have become polluted with microbiological, metal and organic contamination
Part No: AN063Issued year: 2012File size: 0.48mbFile type: pdf
Pyrazines are a class of organic molecules often used to provide flavor to foods. They are typically synthesized but some are found in fruits and vegetables, e.g. grapes, bell peppers, peas, asparagus, beetroot, tobacco, and roasted foods. Pyrazine’s heterocyclic chemistry can yield some challenges to their purification due to the various separation kinetics between the compound and silica. Biotage SNAP Ultra.
Part No: AN123-HORIssued year: 2017File size: 2.18mbFile type: pdf
The US EPA monitors a variety of chemicals in water that may cause harm to humans or wildlife in order to minimize exposure. Method 625 was developed by the Office of Science and Technology in the Clean Water program to monitor a large suite of semivolatile chemicals in wastewater for compliance with the National Pollution Discharge Elimination System (NPDES). NPDES is a system of permitting that regulates the characteristics of water that is released into a waterway, defined by industrial category. The permitting levels are set depending on the waterway’s use.
Part No: P160Issued year: 2017File size: 0.24mbFile type: pdf
Although capable of very high resolution, RP-HPLC is often limited by low column loading capacity, therefore demanding a significant time investment for peptide purification. As an alternative strategy, reversed-phase flash chromatography can also be used to purify synthetic peptides. The larger particle size used in flash column chromatography enables much larger loading capacity, thereby significantly reducing the time required for peptide purification.
Part No: PPS375.v1Issued year: 2015File size: 0.3mbFile type: pdf
User report: Flash instruments. Chugai Pharmaceutical uses Biotage flash chromatography products for drug discovery research. When deciding to convert from manual open-column procedures to automated systems, they chose successive generations of Biotage products, ranging from the Flash+® packed column to the Biotage® Horizon, SP1, Isolera™ Spektra, and Isolera™ Dalton automated flash chromatography systems.
Part No: AN041Issued year: 2001File size: 0.16mbFile type: pdf
Normal-phase flash purification is commonly used by organic chemists in pharmaceutical drug discovery and
process development labs. However, for many synthesized products (e.g. peptides, nucleotides and basic
drug candidates) purification on standard flash silica is not an option due to irreversible adsorption, chemical
interaction and/or solubility issues. Reversed-phase flash purification is an excellent solution for these applications. Yet, this technique has been used sparingly because of perceived lower loading capacity, higher
operating pressures and a scarcity of publications addressing reversed-phase flash chromatography.
Part No: AN082-HORIssued year: 2012File size: 0.85mbFile type: pdf
The focus of this Application Note is to illustrate some of the advances which have been made when performing EPA method 525.2 when using Solid Phase Extraction (SPE). It will make use of the Biotage(r) Horizon SmartPrep Automated Cartridge Extraction system set up to run in Bottle Rinse Mode with 6 mL SPE cartridges.
Part No: AN039Issued year: 2002File size: 0.64mbFile type: pdf
For pilot and production scale purification drugs, the use of a large particle-size media is common. Improving the purification throughput is limited by the media’s large particle size. Such a case was recently encountered when a pharmaceutical company attempted to improve the efficiency of a large-scale purification. In their current process, the use of a 350-600 µm polystyrene-type resin resulted in a lengthy purification cycle and low separation efficiency. However, the labile properties of the targeted component required a shorter purification cycle and high purification.
Part No: AN084-HORIssued year: 2012File size: 1mbFile type: pdf
Within EPA Method 549.2, the suggested rate to load a sample onto a solid phase cartridge is given as 3 to 6 mL/min.
This Application Note outlines the process used to extract diquat and paraquat from water samples using a faster loading rate than given by the EPA in method 549.2
Part No: TN128Issued year: 2006File size: 0.09mbFile type: pdf
This technical note describes the use of derivatization techniques to separate aliphatic
secondary amines from aliphatic tertiary amines in a mixture using the strong cation
exchange sorbent, ISOLUTE® SCX-2.
Part No: AN062-HORIssued year: 2011File size: 0.82mbFile type: pdf
Oftentimes, aqueous samples collected contain varying amounts of suspended solids or sediment strictly due to either the source of the water being sampled or improper sampling techniques. In any circumstance, samples with high amounts of particulates or sediment have proven challenging to extract using EPA Method 3535 Solid Phase Extraction (SPE).
Part No: PPS385Issued year: 2015File size: 4.87mbFile type: pdf
Our carefully selected portfolio of industrial scale products have a proven track record of successful applications and use in scale-up projects. We can support the discovery, development and manufacturing of customer pharmaceutical and biotechnology products, from pre-clinical, phase I, II and III to small scale commercial operations.