Part No: AN057Issued year: 2012File size: 0.21mbFile type: pdf
The formation of diarylethers by reacting an arylhalide and phenol is usually a reaction demanding long reaction times, high temperatures and strong bases, in order to obtain acceptable yield. The substitution patent of the electrophile and the nucleophile affects the reaction times mostly. A sterically hindered electrophile and a strongly deactivated nucleophile as outlined in the (Scheme 1) below, gives a very low yield (13 %) at conventional reflux for 2 weeks.1,2 Remainder was
recovered starting material. We have previously reported the dramatically shortened reaction time to 1 hour along with improved yield running the reaction outlined in the Scheme by heating by microwaves.
Part No: P131Issued year: 2015File size: 0.47mbFile type: pdf
DMSO and DMF are suitable injection solvents for reversed-phase flash purification. DMSO shows it can be loaded in larger volumes (up to 0.05 mL/g of C18 media or 3.5% of a column volume) without affecting chromatographic separations or carrying compounds with it.
Part No: DLV_TN.0111Issued year: 2011File size: 0.08mbFile type: pdf
One of the most common flash purification challenges is
dealing with hard-to-dissolve crude samples. Because polar
solvents cause poor chromatographic results when used as
injection solvents in normal-phase flash chromatography, other
sample load options are needed.
Part No: PPS376Issued year: 2015File size: 1.6mbFile type: pdf
User Case: Kissei Pharmaceutical Co., Ltd. One of Japan’s innovative pharmaceutical companies uses Isolera™ flash
purification systems and Biotage® Initiator+ microwave synthesizers in the
development of new prescription drugs. Modern lab instruments contribute to
efficient use of time and resources at Kissei Pharmaceuticals.
Part No: P143Issued year: 2016File size: 0.27mbFile type: pdf
Buprenorphine and Norbuprenorphine are typically problematic for analysis due to analyte stability issues during sample preparation.
This poster will demonstrate two fast and robust methods for the extraction of buprenorphine and norbuprenorphine in urine (using EVOLUTE EXPRESS CX), oral fluid (using EVOLUTE EXPRESS CX) and whole blood (using ISOLUTE SLE+).
Part No: PN43Issued year: 2011File size: 0.27mbFile type: pdf
Endogenous phospholipids present in biological fluids are a major problem in LCMS/ MS analysis as they are often very difficult to remove during sample preparation. When phospholipids are not removed, they retain very strongly on reversed phase analytical columns. If high organic (end of run) washes are not incorporated into the LC methods these matrix components may elute in subsequent analyses causing regions of suppression/enhancement leading to inaccurate quantitation. This poster evaluates the use of polymer-based solid phase extraction (SPE) sorbents, incorporating hydrophobic and various mixedmode retention mechanisms to address the problems associated with phospholipid removal.
Phospholipid, EVOLUTE, STRATA X, OASIS, WATERS, AX, WAX, CX, WCX, ABN, ASMS 2011
Part No: P078Issued year: 2014File size: 0.25mbFile type: pdf
This poster focuses on the different strategies that can be employed when using EVOLUTE SPE sorbents (with both single and dual retention mechanisms) to reduce or eliminate residual phospholipids in sample extracts.
Part No: P032Issued year: 2011File size: 1.35mbFile type: pdf
Endogenous phospholipids (outline structure shown in
Figure 1.) present in biological fluids are a major problem
in LC-MS/MS analysis. Due to their strong retention
characteristics in reversed phase chromatography
phospholipids tend not to elute as discrete peaks and are
often very difficult to separate from analytes of interest.
This co-elution often leads to areas of suppression or enhancement in the chromatogram which in turn can cause
quantitation issues. Supported liquid extraction (SLE) is an
analogous technique to traditional liquidliquid
extraction. This poster compares phospholipid removal using a wide variety of solvent combinations, pH control and polar extraction solvents on supported liquid extraction plates
Part No: Issued year: 2011File size: 1.65mbFile type: pdf
User Report: Syro I, University of Tokyo. The Suga Laboratory at RCAST, University of Tokyo, uses the Biotage Syro I automated peptide synthesizer for scaling up the chemical synthesis of non-standard peptides.
Part No: 412941-DIssued year: 2012File size: 1.18mbFile type: pdf
ELSD-1080 (evaporative light-scattering detector) is a
universal detector designed for use with Isolera One
and Isolera Four systems when purifying compounds
with little or no UV absorption such as carbohydrates,
steroids, lipids, and terpenes
Part No: AN084Issued year: 2014File size: 0.86mbFile type: pdf
This application note outlines how to use the Isolera system to perform a size-exclusion separation as part of a sample clean up method defined by the EPA, a key sample preparation step in environmental laboratories.
Part No: 951.v.1.Issued year: 2010File size: 0.07mbFile type: pdf
The following describes matrix spike and surrogate spike recovery from soil samples using Biotage TurboVap II Concentration workstation. The data provided comes from a variety of actual soil samples analyzed in the laboratory. The data provided comes from a variety of actual soil samples analyzed in the laboratory.
Part No: P128Issued year: 2015File size: 0.26mbFile type: pdf
In all areas of analytical laboratory testing it is vital to ensure proper quality measures are in place to reduce or eliminate cross contamination between samples, which could result in false positive and/or false negative results. In many cases sample carryover in the LC/MS system is checked early on in the method development process. However, one area that can often be overlooked the sample preparation stage. This involves all aspects including pipetting, sample transfer, extraction protocol, evaporation and mixing steps. This poster examines various stages of the sample preparation process to determine the potential for cross contamination and present approaches to minimize and or eliminate the effect. This is demonstrated via a series of dye experiments combined with analyte testing using LC-MS/MS.
Part No: P126Issued year: 2015File size: 0.48mbFile type: pdf
This poster demonstrates the use of a novel protein and phospholipid depletion plate, for the extraction of 25-hydroxy vitamin D from serum. The extraction protocol was ultimately transferred to an SPE automation platform and method performance versus manual processing was compared.
Part No: P079Issued year: 2014File size: 0.59mbFile type: pdf
The new ISOLUTE® PLD+ Protein and Phospholipid Removal Plate is highlighted in this poster. Protein and phospholipid removal, and analyte recovery are included, along with data illustrating the positive impact of clean (PL and protein free) samples in maintaining analyte signal intensity and low UPLC column back pressure over multiple LCMS runs.
Part No: P088Issued year: 2014File size: 1.06mbFile type: pdf
This poster evaluates the performance of a novel 96-well filter plate (ISOLUTE PLD+ Protein and Phospholipid Removal Plate) for
the simultaneous removal of proteins and phospholipids from serum samples prior to LC-MS/MS analysis.
Part No: P104Issued year: 2014File size: 0.77mbFile type: pdf
This poster presents the ISOLUTE PLD+ Protein and Phospholipid removal plate, highlighting its ease of use and excellent performance with respect to sample clean up, analyte recovery and elimination of back pressure build up in the UPLC system.